This patch contains several fixes to enable vPMU under TCG mode. It
first removes the checking of kvm_enabled() while unsetting
ARM_FEATURE_PMU. With it, the .pmu option can be used to turn on/off vPMU
under TCG mode. Secondly the PMU node of DT table is now created under TCG.
The last fix is to disable the masking of PMUver field of ID_AA64DFR0_EL1.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1486504171-26807-5-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AHCI emulation code supports 64-bit addressing and should advertise this
fact in the Host Capabilities register. Both Linux and Windows drivers test
this bit to decide if the upper 32 bits of various registers may be written
to, and at least some versions of Windows have a bug where DMA is attempted
with an address above 4GB but, in the absence of HOST_CAP_64, the upper 32
bits are left unititialized which leads to a memory corruption.
[Maintainer edit:
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=1411105,
which affects Windows Server 2008 SP2 in some cases.]
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Message-id: 1484305370-6220-1-git-send-email-lprosek@redhat.com
[Amended commit message --js]
Signed-off-by: John Snow <jsnow@redhat.com>
This reverts commit 5858dd1801.
Conflicts:
hw/display/cirrus_vga.c
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-id: 1486645341-5010-2-git-send-email-kraxel@redhat.com
The blit_region_is_unsafe checks don't work correctly for the
patterncopy source. It's a fixed-sized region, which doesn't
depend on cirrus_blt_{width,height}. So go do the check in
cirrus_bitblt_common_patterncopy instead, then tell blit_is_unsafe that
it doesn't need to verify the source. Also handle the case where we
blit from cirrus_bitbuf correctly.
This patch replaces 5858dd1801.
Security impact: I think for the most part error on the safe side this
time, refusing blits which should have been allowed.
Only exception is placing the blit source at the end of the video ram,
so cirrus_blt_srcaddr + 256 goes beyond the end of video memory. But
even in that case I'm not fully sure this actually allows read access to
host memory. To trick the commit 5858dd18 security checks one has to
pick very small cirrus_blt_{width,height} values, which in turn implies
only a fraction of the blit source will actually be used.
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-id: 1486645341-5010-1-git-send-email-kraxel@redhat.com
When the guest sends VIRTIO_GPU_CMD_RESOURCE_UNREF without detaching the
backing storage beforehand (VIRTIO_GPU_CMD_RESOURCE_DETACH_BACKING)
we'll leak memory.
This patch fixes it for 3d mode, simliar to the 2d mode fix in commit
"b8e2392 virtio-gpu: call cleanup mapping function in resource destroy".
Reported-by: 李强 <liqiang6-s@360.cn>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485167210-4757-1-git-send-email-kraxel@redhat.com
In virtio_gpu_set_scanout function, when creating the 'rect'
its refcount is set to 2, by pixman_image_create_bits and
qemu_create_displaysurface_pixman function. This can lead
a memory leak issues. This patch avoid this issue.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 5884626f.5b2f6b0a.1bfff.3037@mx.google.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Use the 'unimplemented' dummy device to cover regions of the
SoC device memory map which we don't have proper device
implementations for yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484247815-15279-4-git-send-email-peter.maydell@linaro.org
Create a new "unimplemented" sysbus device, which simply accepts
all read and write accesses, and implements them as read-as-zero,
write-ignored, with logging of the access as LOG_UNIMP.
This is useful for stubbing out bits of an SoC or board model
which haven't been written yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484247815-15279-3-git-send-email-peter.maydell@linaro.org
Since the integratorcp board creates the CPU object directly
rather than via cpu_arm_init(), we have to call the CPU
class parse_features() method ourselves if we want to
support the user passing features via the -cpu command
line argument as well as just the cpu name. Do so.
Signed-off-by: Julian Brown <julian@codesourcery.com>
[PMM: split out into its own patch]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While doing multi block SDMA transfer in routine
'sdhci_sdma_transfer_multi_blocks', the 's->fifo_buffer' starting
index 'begin' and data length 's->data_count' could end up to be same.
This could lead to an OOB access issue. Correct transfer data length
to avoid it.
Cc: qemu-stable@nongnu.org
Reported-by: Jiang Xin <jiangxin1@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20170130064736.9236-1-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables reboot of a guest from U-Boot and Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC includes a set of watchdog timers using 32-bit
decrement counters, which can be based either on the APB clock or
a 1 MHz clock.
The watchdog timer is designed to prevent system deadlock and, in
general, it should be restarted before timeout. When a timeout occurs,
different types of signals can be generated, ARM reset, SOC reset,
System reset, CPU Interrupt, external signal or boot from alternate
block. The current model only performs the system reset function as
this is used by U-Boot and Linux.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-2-git-send-email-clg@kaod.org
[clg: - fixed compile breakage
- fixed io region size
- added watchdog_perform_action() on timer expiry
- wrote a commit log
- merged fixes from Andrew Jeffery to scale the reload value ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VMState added by this patch preserves correct
loading of the integratorcp device state.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-id: 20170131114310.6768.79416.stgit@PASHA-ISP
[PMM: removed unnecessary minimum_version_id_old lines]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Check qdev's call to vmstate_register_with_alias_id; that gets
most of the common uses; there's hundreds of calls via vmstate_register
which could get fixed over time.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-4-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
I'll be adding an error to it in a subsequent patch.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-2-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The qemu xhci emulation doesn't handle the ERDP_EHB flag correctly.
When the host adapter queues a new event the ERDP_EHB flag is set. The
flag is cleared (via w1c) by the guest when it updates the ERDP (event
ring dequeue pointer) register to notify the host adapter which events
it has fetched.
An IRQ must be raised in case the ERDP_EHB flag flips from clear to set.
If the flag is set already (which implies there are events queued up
which are not yet processed by the guest) xhci must *not* raise a IRQ.
Qemu got that wrong and raised an IRQ on every event, thereby generating
spurious interrupts in case we've queued events faster than the guest
processed them. This patch fixes that.
With that change in place we also have to check ERDP updates, to see
whenever the guest has fetched all queued events. In case there are
still pending events set ERDP_EHB and raise an IRQ again, to make sure
the events don't linger unseen forever.
The linux kernel driver and the microsoft windows driver (shipped with
win8+) can deal with the spurious interrupts without problems. The
renesas windows driver (v2.1.39) which can be used on older windows
versions is quite upset though. It does spurious ERDP updates now and
then (not every time, seems we must hit a race window for this to
happen), which in turn makes the qemu xhci emulation think the event
ring is full. Things go south from here ...
tl;dr: This is the "fix xhci on win7" patch.
Cc: M.Cerveny@computer.org
Cc: 1373228@bugs.launchpad.net
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1486104705-13761-1-git-send-email-kraxel@redhat.com
CCID device emulator uses Application Protocol Data Units(APDU)
to exchange command and responses to and from the host.
The length in these units couldn't be greater than 65536. Add
check to ensure the same. It'd also avoid potential integer
overflow in emulated_apdu_from_guest.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170202192228.10847-1-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
xhci_submit and xhci_fire_ctl_transfer are is called from
xhci_kick_epctx processing loop only, so there is no need to call
xhci_kick_epctx make sure processing continues. Also eecursive calls
into xhci_kick_epctx can cause trouble.
Drop the xhci_kick_epctx calls.
Cc: 1653384@bugs.launchpad.net
Fixes: 94b037f2a4
Reported-by: Fabian Lesniak <fabian@lesniak-it.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485790607-31399-4-git-send-email-kraxel@redhat.com
Make clear that this isn't guaranteed to actually complete the transfer,
the usb packet can still be in flight after calling that function.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485790607-31399-3-git-send-email-kraxel@redhat.com
Windows 10 reportedly sends these, so accept them in case
the device in question is a superspeed (usb3) device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485870727-21956-2-git-send-email-kraxel@redhat.com
Print some more details in case we get a unknown
control request, to ease trouble-shooting.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485870727-21956-1-git-send-email-kraxel@redhat.com
1. Set bInterfaceProtocol to 0x00 for usb-tablet. This should be
non-zero for boot protocol devices only, which the usb-tablet is not.
2. Set the usb-tablet's usage to "mouse" in the report descriptor.
The boot protocol of 0x02 specifically confused OS X/macOS' HID driver
stack, causing it to generate additional bogus HID events with relative
motion in addition to the tablet's absolute coordinate events.
Absolute pointing devices with HID Report Descriptor usage of 0x01
(pointing) are treated by the macOS HID driver as analog sticks, and
absolute coordinates are not directly translated to absolute mouse
cursor positions. Changing it to 0x02 (mouse) fixes the problem, and
does not have any adverse effect in other operating systems and
windowing systems. (VMWare does the same thing.)
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Message-id: 1485365075-32702-1-git-send-email-phil@philjordan.eu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The m48t59 device supports both ISA and direct sysbus attached versions of
the device in the one .c file. This can be awkward for some embedded
machine types which need the sysbus M48T59, but don't want to pull in the
ISA bus code and its other dependencies.
Therefore, this patch splits out the code for the ISA attached M48T59 into
its own C file. It will be built when both CONFIG_M48T59 and
CONFIG_ISA_BUS are enabled.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Currently, the code to handle the legacy ISA bus is always included in
qemu. However there are lots of platforms that don't include ISA legacy
devies, and quite a few that have never used ISA legacy devices at all.
This patch allows the ISA bus code to be disabled in the configuration for
platforms where it doesn't make sense.
For now, the default configs are adjusted to include ISA on all platforms
including PCI: anything with PCI can at least in principle add an i82378
PCI->ISA bridge. Also, CONFIG_IDE_CORE which is already in pci.mak
requires ISA support.
We also explicitly enable ISA on some other non-PCI platforms which include
ISA devices: moxie, sparc and unicore32. We may want to pare this down in
future.
The platforms that will lose ISA by default are: cris, lm32, microblazeel,
microblaze, openrisc, s390x, tricore, xtensaeb, xtensa. As far as I can
tell none of these ever used ISA.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
At present, the core device model code for 8250-like serial ports
(serial.c) and the code for serial ports attached to ISA-style legacy IO
(serial-isa.c) are both controlled by the CONFIG_SERIAL variable.
There are lots and lots of embedded platforms that have 8250-like serial
ports but have never had anything resembling ISA legacy IO. Therefore,
split serial-isa into its own CONFIG_SERIAL_ISA option so it can be
disabled for platforms where it's not appropriate.
For now, I enabled CONFIG_SERIAL_ISA in every default-config where
CONFIG_SERIAL is enabled, excepting microblaze, or32, and xtensa. As best
as I can tell, those platforms never used legacy ISA, and also don't
include PCI support (which would allow connection of a PCI->ISA bridge
and/or a southbridge including legacy ISA serial ports).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vLVl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170202' into staging
ppc patch queue 2017-02-02
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
# gpg: Signature made Thu 02 Feb 2017 01:40:16 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170202: (107 commits)
hw/ppc/pnv: Use error_report instead of hw_error if a ROM file can't be found
ppc/kvm: Handle the "family" CPU via alias instead of registering new types
target/ppc/mmu_hash64: Fix incorrect shift value in amr calculation
target/ppc/mmu_hash64: Fix printing unsigned as signed int
tcg/POWER9: NOOP the cp_abort instruction
target/ppc/debug: Print LPCR register value if register exists
target-ppc: Add xststdc[sp, dp, qp] instructions
target-ppc: Add xvtstdc[sp,dp] instructions
target-ppc: Add MMU model check for booke machines
ppc: switch to constants within BUILD_BUG_ON
target/ppc/cpu-models: Fix/remove bad CPU aliases
target/ppc: Remove unused POWERPC_FAMILY(POWER)
spapr: clock should count only if vm is running
ppc: Remove unused function cpu_ppc601_rtc_init()
target/ppc: Add pcr_supported to POWER9 cpu class definition
powerpc/cpu-models: rename ISAv3.00 logical PVR definition
target-ppc: Add xvcv[hpsp, sphp] instructions
target-ppc: Add xsmulqp instruction
target-ppc: Add xsdivqp instruction
target-ppc: Add xscvsdqp and xscvudqp instructions
...
# Conflicts:
# hw/pci-bridge/Makefile.objs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The error exits of xen_pv_find_xendev() free the new xen-device via
g_free() which is wrong.
As the xen-device has been initialized as qdev it must be removed
via qdev_unplug().
This bug has been introduced with commit 3a6c9172ac
("xen: create qdev for each backend device").
Reported-by: Roger Pau Monné <roger.pau@citrix.com>
Tested-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
- build error with old gcc versions
- race between cmma reset and rom/loader resets
- linux-user vs. cpu model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=hOry
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/s390x-20170201' into staging
s390x fixes
- build error with old gcc versions
- race between cmma reset and rom/loader resets
- linux-user vs. cpu model
# gpg: Signature made Wed 01 Feb 2017 08:24:47 GMT
# gpg: using RSA key 0x117BBC80B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
# Primary key fingerprint: F922 9381 A334 08F9 DBAB FBCA 117B BC80 B5A6 1C7C
* remotes/borntraeger/tags/s390x-20170201:
target/s390x: use "qemu" cpu model in user mode
s390x/kvm: fix small race reboot vs. cmma
s390-pci: fix compilation on older GCC versions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing bitblt copy in backward mode, we should minus the
blt width first just like the adding in the forward mode. This
can avoid the oob access of the front of vga's vram.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
{ kraxel: with backward blits (negative pitch) addr is the topmost
address, so check it as-is against vram size ]
Cc: qemu-stable@nongnu.org
Cc: P J P <ppandit@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Fixes: d3532a0db0 (CVE-2014-8106)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485938101-26602-1-git-send-email-kraxel@redhat.com
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
generic pci root port support
disable shpc by default
safer version of ARRAY_SIZE and QEMU_BUILD_BUG_ON
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYkTwaAAoJECgfDbjSjVRpHHoIALlEhk7iZJvjJBiT0BQ51lGB
uU0fq+8H2G+WZoM83dpSv/pG1Ob6SZtiehsXWf+6Za+AgnU3STCZDXGKo9Jxs2EO
jp73puewWCq69VMyjGnGEWWh4bf41xjWYVrhVrY9LSz7u6hCM9sdWPRy/PGLSlLo
s3xgYefGdtol0S5qMdb4LOb2tfcdGYHADyMiERT994pmfZKrBMXlHlVM0jOo5ytw
zknRh4JwH+zZMQPczrvWUTjdxRE0UIUd4fFz9cRwX8F6zVpAbKAT2Ird2jGNlpyh
jQBX+sxXQR3u+mjZDxZBYbpxOZARUTriagAJPs343uIUCPOmvVXsluidF9bkU+A=
=ZBEs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, pci: fixes, features
generic pci root port support
disable shpc by default
safer version of ARRAY_SIZE and QEMU_BUILD_BUG_ON
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 01 Feb 2017 01:38:34 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
arm: add trailing ; after MISMATCH_CHECK
arm: better stub version for MISMATCH_CHECK
hw/pci: disable pci-bridge's shpc by default
vhost-user: delete chardev on cleanup
vhost: skip ROM sections
virtio: make virtio_should_notify static
pci: Convert msix_init() to Error and fix callers
hcd-xhci: check & correct param before using it
msix: Follow CODING_STYLE
hw/i386: check if nvdimm is enabled before plugging
hw/pcie: Introduce Generic PCI Express Root Port
hw/ioh3420: derive from PCI Express Root Port base class
hw/pcie: Introduce a base class for PCI Express Root Ports
intel_iommu: fix and simplify size calculation in process_device_iotlb_desc()
pci: mark ROMs read-only
ARRAY_SIZE: check that argument is an array
compiler: expression version of QEMU_BUILD_BUG_ON
compiler: rework BUG_ON using a struct
QEMU_BUILD_BUG_ON: use __COUNTER__
ppc: switch to constants within BUILD_BUG_ON
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw_error() is for CPU related errors only (it dumps the CPU registers
and calls abort()!), so using error_report() is the better choice
of reporting an error in case we simply did not find a file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Machines bamboo, e500 and virtex-ml507 assume a certain MMU model,
otherwise resulting in unpredictable behavior. Add apropriate checks
into *_init functions.
Signed-off-by: Valentin Plotkin <caliborn@sdf.org>
[regarding virtex parts]
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Apply the cirrus_addr_mask to cirrus_blt_dstaddr and cirrus_blt_srcaddr
right after assigning them, in cirrus_bitblt_start(), instead of having
this all over the place in the cirrus code, and missing a few places.
Reported-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485338996-17095-1-git-send-email-kraxel@redhat.com
The rops used by cirrus_bitblt_common_patterncopy only use
the destination pitch, so the source pitch shoul allowed to
be zero and the blit with used for the range check around the
source address.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Message-id: 1485272138-23249-1-git-send-email-w.bumiller@proxmox.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
cirrus_invalidate_region() calls memory_region_set_dirty()
on a per-line basis, always ranging from off_begin to
off_begin+bytesperline. With a negative pitch off_begin
marks the top most used address and thus we need to do an
initial shift backwards by a line for negative pitches of
backward blits, otherwise the first iteration covers the
line going from the start offset forwards instead of
backwards.
Additionally since the start address is inclusive, if we
shift by a full `bytesperline` we move to the first address
*not* included in the blit, so we only shift by one less
than bytesperline.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Message-id: 1485352137-29367-1-git-send-email-w.bumiller@proxmox.com
[ kraxel: codestyle fixes ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Right now we reset all devices before we reset the cmma states. This
can result in the host kernel discarding guest pages that were
previously in the unused state but already contain a bios or a -kernel
file before the cmma reset has finished. This race results in random
guest crashes or hangs during very early reboot.
Fixes: 1cd4e0f6f0 ("s390x/cmma: clean up cmma reset")
Cc: qemu-stable@nongnu.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
S390PCIBusDevice is typedef'ed earlier in the file, before the hunks
that this patch modifies. The double typedef causes old versions of
GCC to complain.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1485523252-88288-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The shpc component is optional while ACPI hotplug is used
for hot-plugging PCI devices into a PCI-PCI bridge.
Disabling the shpc by default will make slot 0 usable at boot time
and not only for hot-plug, without loosing any functionality.
Older machines will have shpc enabled for compatibility reasons.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost does not support RO protections on memory at the moment - adding
ROMs would mean that e.g. a buggy guest might change them in-memory - a
condition from which guest reset does not recover. Not nice.
We also definitely don't want to try logging writes into ROMs -
in particular guests set very high addresses for ROM BARs
so logging these writes would waste a lot of memory.
Maybe ROMs could be supported with the iotlb variant -
not sure, but there seems to be no good reason for virtio
to try to do DMA from ROM. So let's just skip ROM memory.
Suggested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
msix_init() reports errors with error_report(), which is wrong when
it's used in realize(). The same issue was fixed for msi_init() in
commit 1108b2f. In order to make the API change as small as possible,
leave the return value check to later patch.
For some devices(like e1000e, vmxnet3, nvme) who won't fail because of
msix_init's failure, suppress the error report by passing NULL error
object.
Bonus: add comment for msix_init.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Hannes Reinecke <hare@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
usb_xhci_realize() corrects invalid values of property "intrs"
automatically, but the uncorrected value is passed to msi_init(),
which chokes on invalid values. Delay that until after the
correction.
Resources allocated by usb_xhci_init() are leaked when msi_init()
fails. Fix by calling it after msi_init().
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The missing of 'nvdimm' in the machine type option '-M' means NVDIMM
is disabled. QEMU should refuse to plug any NVDIMM device in this case
and report the misconfiguration.
The behavior of NVDIMM on unsupported platform (HW/FW) is vendor
specific. For some vendors, it's undefined and the platform may do
anything. Thus, I think QEMU is free to choose the implementation.
Aborting QEMU (i.e. refusing to boot) is the easiest one.
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Message-Id: 20170112110928.GF4621@stefanha-x1.localdomain
Message-Id: 20170111093630.2088-1-stefanha@redhat.com
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The Generic Root Port behaves almost the same as the
Intel's IOH device with id 3420, without having
Intel specific attributes.
The device has two purposes:
(1) Can be used on both X86 and ARM machines.
(2) It will allow us to tweak the behaviour
(e.g add vendor-specific PCI capabilities)
- something that obviously cannot be done
on a known device.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Preserve only Intel specific details.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The 'base' PCI Express Root Port includes
the common code to be re-used for all
Root Ports implementations. Most of the code
was taken from the current implementation
of Intel's IOH 3420 Root Port.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We don't use 1ULL which is wrong during size calculation. Fix it, and
while at it, switch to use cto64() and adds a comments to make it
simpler and easier to be understood.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Looks like we didn't mark PCI ROMs as RO allowing
mischief such as guests writing there.
Further, e.g. vhost gets confused trying to allocate
enough space to log writes there. Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
We are switching BUILD_BUG_ON to verify that it's parameter is a
compile-time constant, and it turns out that some gcc versions
(specifically gcc (Ubuntu 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609) are
not smart enough to figure it out for expressions involving local
variables. This is harmless but means that the check is ineffective for
these platforms. To fix, replace the variable with macros.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are a number of unused trace events that
scripts/cleanup-trace-events.pl finds. The "hw/vfio/pci-quirks.c"
filename was typoed and "qapi/qapi-visit-core.c" was missing the qapi/
directory prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170126171613.1399-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Introduce rules in the top level Makefile that are able to generate
trace.[ch] files in every subdirectory which has a trace-events file.
The top level directory is handled specially, so instead of creating
trace.h, it creates trace-root.h. This allows sub-directories to
include the top level trace-root.h file, without ambiguity wrt to
the trace.g file in the current sub-dir.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-7-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The trace-events for a given source file should generally
always live in the same directory as the source file.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-5-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The trace-events for a given source file should generally
always live in the same directory as the source file.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-4-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The trace-events for a given source file should generally
always live in the same directory as the source file.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-3-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We are switching BUILD_BUG_ON to verify that it's parameter is a
compile-time constant, and it turns out that some gcc versions
(specifically gcc (Ubuntu 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609) are
not smart enough to figure it out for expressions involving local
variables. This is harmless but means that the check is ineffective for
these platforms. To fix, replace variables with macros.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This enables the ps2 controller to process mouse events for buttons 4 and 5.
Additionally, distinct definitions for the ps2 mouse button state are
introduced. The legacy definitions from console.h are not used anymore.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Message-id: 20161206190007.7539-3-fabian@lesniak-it.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We are switching BUILD_BUG_ON to verify that it's parameter is a
compile-time constant, and it turns out that some gcc versions
(specifically gcc (Ubuntu 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609) are
not smart enough to figure it out for expressions involving local
variables. This is harmless but means that the check is ineffective for
these platforms. To fix, replace the variable with macros.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[dwg: Correct a printf format warning]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a port to ppc of the i386 commit:
00f4d64 kvmclock: clock should count only if vm is running
We remove timebase_post_load function, and use the VM state
change handler to save and restore the guest_timebase (on stop
and continue).
We keep timebase_pre_save to reduce the clock difference on
migration like in:
6053a86 kvmclock: reduce kvmclock difference on migration
Time base offset has originally been introduced by commit
98a8b52 spapr: Add support for time base offset migration
So while VM is paused, the time is stopped. This allows to have
the same result with date (based on Time Base Register) and
hwclock (based on "get-time-of-day" RTAS call).
Moreover in TCG mode, the Time Base is always paused, so this
patch also adjust the behavior between TCG and KVM.
VM state field "time_of_the_day_ns" is now useless but we keep
it to be able to migrate to older version of the machine.
As vmstate_ppc_timebase structure (with timebase_pre_save() and
timebase_post_load() functions) was only used by vmstate_spapr,
we register the VM state change handler only in ppc_spapr_init().
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is completely unused, thus it can be removed without problems.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If the DECAR register is set to 0, QEMU tries to reload the decrementer with
zero in an inifinite loop. According to PPC documentation, the decrementer is
triggered on 1->0 transition, so avoid reloading the decrementer if if is
already zero.
The problem does not manifest under Linux, but it is valid to set DECAR to zero
(and may make sense as part of decrementer initialization when interrupts are
disabled).
Signed-off-by: Roman Kapl <rka@sysgo.com>
[dwg: Fixed style nit]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Once a compatiblity mode is negotiated with the guest,
h_client_architecture_support() uses run_on_cpu() to update each CPU to
the new mode. We're going to want this logic somewhere else shortly,
so make a helper function to do this global update.
We put it in target-ppc/compat.c - it makes as much sense at the CPU level
as it does at the machine level. We also move the cpu_synchronize_state()
into ppc_set_compat(), since it doesn't really make any sense to call that
without synchronizing state.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
During boot, PAPR guests negotiate CPU model support with the
ibm,client-architecture-support mechanism. The logic to implement this in
qemu is very convoluted. This cleans it up to be cleaner, using the new
ppc_check_compat() call.
The new logic for choosing a compatibility mode is:
1. Usually, use the most recent compatibility mode that is
a) supported by the guest
b) supported by the CPU
and c) no later than the maximum allowed (if specified)
2. If no suitable compatibility mode was found, the guest *does*
support this CPU explicitly, and no maximum compatibility mode is
specified, then use "raw" mode for the current CPU
3. Otherwise, fail the boot.
This differs from the results of the old code: the old code preferred using
"raw" mode to a compatibility mode, whereas the new code prefers a
compatibility mode if available. Using compatibility mode preferentially
means that we're more likely to be able to migrate the guest to a similar
but not identical host.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PCI Expander Bridge (PXB) device is essentially a hack to allow
different PCIe devices to be assigned to different NUMA nodes on x86. Each
PXB is sort-of a separate PCI host bridge, except that its config space
is shared with the config space of the main PCI host bridge, rather than
being independent.
This is only necessary if the platform doesn't (easily) allow truly
independent PCI host bridges. AFAIK that's just x86.
This patch makes it possible to configure PXB out of the build, and adjusts
the default configs so it's only included on x86 targets.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Machine supports both Open Hack'Ware and OpenBIOS.
Open Hack'Ware is the default because OpenBIOS is currently unable to boot
PReP boot partitions or PReP kernels.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[dwg: Correct compile failure with KVM located by Thomas Huth]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Added CONFIG_RS6000_MC to ppc64 or it breaks testcases]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This device is a partial duplicate of System I/O device available in hw/ppc/prep.c
This new one doesn't have all the Motorola-specific registers.
The old one should be deprecated and removed with the 'prep' machine.
Partial documentation available at
ftp://ftp.software.ibm.com/rs6000/technology/spec/srp1_1.exe
section 6.1.5 (I/O Device Mapping)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
* Drop the old SysBus init function and use instance_init
* Change mpc8xxx_gpio_reset to a DeviceClass::reset function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To continue consolidation of compatibility mode information, this rewrites
the ppc_get_compat_smt_threads() function using the table of compatiblity
modes in target-ppc/compat.c.
It's not a direct replacement, the new ppc_compat_max_threads() function
has simpler semantics - it just returns the number of threads the cpu
model has, taking into account any compatiblity mode it is in.
This no longer takes into account kvmppc_smt_threads() as the previous
version did. That check wasn't useful because we check in
ppc_cpu_realizefn() that CPUs aren't instantiated with more threads
than kvm allows (or if we didn't things will already be broken and
this won't make it any worse).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
When passing through an USB storage device to a pseries guest, it
is currently not possible to automatically boot from the device
if the "bootindex" property has been specified, too (e.g. when using
"-device nec-usb-xhci -device usb-host,hostbus=1,hostaddr=2,bootindex=0"
at the command line). The problem is that QEMU builds a device tree path
like "/pci@800000020000000/usb@0/usb-host@1" and passes it to SLOF
in the /chosen/qemu,boot-list property. SLOF, however, probes the
USB device, recognizes that it is a storage device and thus changes
its name to "storage", and additionally adds a child node for the
SCSI LUN, so the correct boot path in SLOF is something like
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000" instead.
So when we detect an USB mass storage device with SCSI interface,
we've got to adjust the firmware boot-device path properly that
SLOF can automatically boot from the device.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1354177
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_SIGNAL_SYS_RESET hcall allows a guest CPU to raise a system reset
exception on CPUs within the same guest -- all CPUs, all-but-self, or a
specific CPU (including self).
This has not made its way to a PAPR release yet, but we have an hcall
number assigned.
H_SIGNAL_SYS_RESET = 0x380
Syntax:
hcall(uint64 H_SIGNAL_SYS_RESET, int64 target);
Generate a system reset NMI on the threads indicated by target.
Values for target:
-1 = target all online threads including the caller
-2 = target all online threads except for the caller
All other negative values: reserved
Positive values: The thread to be targeted, obtained from the value
of the "ibm,ppc-interrupt-server#s" property of the CPU in the OF
device tree.
Semantics:
- Invalid target: return H_Parameter.
- Otherwise: Generate a system reset NMI on target thread(s),
return H_Success.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'cpu_version' field in PowerPCCPU is badly named. It's named after the
'cpu-version' device tree property where it is advertised, but that meaning
may not be obvious in most places it appears.
Worse, it doesn't even really correspond to that device tree property. The
property contains either the processor's PVR, or, if the CPU is running in
a compatibility mode, a special "logical PVR" representing which mode.
Rename the cpu_version field, and a number of related variables to
compat_pvr to make this clearer.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The pseries machine type is a bit unusual in that it runs a paravirtualized
guest. The guest expects to interact with a hypervisor, and qemu
emulates the functions of that hypervisor directly, rather than executing
hypervisor code within the emulated system.
To implement this in TCG, we need to intercept hypercall instructions and
direct them to the machine's hypercall handlers, rather than attempting to
perform a privilege change within TCG. This is controlled by a global
hook - cpu_ppc_hypercall.
This cleanup makes the handling a little cleaner and more extensible than
a single global variable. Instead, each CPU to have hypercalls intercepted
has a pointer set to a QOM object implementing a new virtual hypervisor
interface. A method in that interface is called by TCG when it sees a
hypercall instruction. It's possible we may want to add other methods in
future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
spapr_h_cas_compose_response() includes a cpu_update parameter which
controls whether it includes updated information on the CPUs in the device
tree fragment returned from the ibm,client-architecture-support (CAS) call.
Providing the updated information is essential when CAS has negotiated
compatibility options which require different cpu information to be
presented to the guest. However, it should be safe to provide in other
cases (it will just override the existing data in the device tree with
identical data). This simplifies the code by removing the parameter and
always providing the cpu update information.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Currently the pseries machine has two paths for constructing CPUs. On
newer machine type versions, which support cpu hotplug, it constructs
cpu core objects, which in turn construct CPU threads. For older machine
versions it individually constructs the CPU threads.
This division is going to make some future changes to the cpu construction
harder, so this patch unifies them. Now cpu core objects are always
created. This requires some updates to allow core objects to be created
without a full complement of threads (since older versions allowed a
number of cpus not a multiple of the threads-per-core). Likewise it needs
some changes to the cpu core hot/cold plug path so as not to choke on the
old machine types without hotplug support.
For good measure, we move the cpu construction to its own subfunction,
spapr_init_cpus().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
The Xen HVM unplug protocol [1] specifies a mechanism to allow guests to
request unplug of 'aux' disks (which is stated to mean all IDE disks,
except the primary master). This patch adds support for that unplug request.
NOTE: The semantics of what happens if unplug of all disks and 'aux' disks
is simultaneously requests is not clear. The patch makes that
assumption that an 'all' request overrides an 'aux' request.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=blob;f=docs/misc/hvm-emulated-unplug.markdown
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
----
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: John Snow <jsnow@redhat.com>
...not just IDE and SCSI.
This patch allows the Xen tool-stack to fully support of NVMe as an
emulated disk type. See [1] for the relevant tool-stack patch discussion.
[1] https://lists.xen.org/archives/html/xen-devel/2017-01/msg01225.html
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
The current code is poorly structured and potentially leads to multiple
config space reads when one is sufficient. Also the UNPLUG_ALL_IDE_DISKS
flag is mis-named since it also results in SCSI disks being unplugged.
This patch renames the flag and re-structures the code to be more
efficient, and readable.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Turn Chardev into Object.
qemu_chr_alloc() is replaced by the qemu_chardev_new() constructor. It
will call qemu_char_open() to open/intialize the chardev with the
ChardevCommon *backend settings.
The CharDriver::create() callback is turned into a ChardevClass::open()
which is called from the newly introduced qemu_chardev_open().
"chardev-gdb" and "chardev-hci" are internal chardev and aren't
creatable directly with -chardev. Use a new internal flag to disable
them. We may want to use TYPE_USER_CREATABLE interface instead, or
perhaps allow -chardev usage.
Although in general we keep typename and macros private, unless the type
is being used by some other file, in this patch, all types and common
helper macros for qemu-char.c are in char.h. This is to help transition
now (some types must be declared early, while some aren't shared) and
when splitting in several units. This is to be improved later.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use common allocator for CharDriverState.
Rename the now untouched parent field.
The casts added are temporary, they are replaced with QOM type-safe
macros in a later patch in this series.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a single allocation for CharDriverState, this avoids extra
allocations & pointers, and is a step towards more object-oriented
CharDriver.
Gtk console is a bit peculiar, gd_vc_chr_set_echo() used to have a
temporary VirtualConsole to save the echo bit. Instead now, we consider
whether vcd->console is set or not, and restore the echo bit saved in
VCDriverState when calling gd_vc_vte_init().
The casts added are temporary, they are replaced with QOM type-safe
macros in a later patch in this series.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes the code more declarative, and avoids duplicating the
information on all instances.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When running with debug enabled, the scsi-generic cdb that is
dumped skips byte 0 of the command, which is the opcode. This
makes identifying which command is being issued/completed a
little difficult. Example:
0x00 0x00 0x01 0x00 0x00
scsi-generic: scsi_read_data 0x0
scsi-generic: Data ready tag=0x0 len=164
scsi-generic: scsi_read_data 0x0
scsi-generic: Command complete 0x0x10a42c60 tag=0x0 status=0
Improve this by adding a message prior to the loop, similar to
what exists for scsi-disk. Clean up a few other messages to be
more explicit of what is being represented. Example:
scsi-generic: Command: data=0x12 0x00 0x00 0x01 0x00 0x00
scsi-generic: scsi_read_data tag=0x0
scsi-generic: Data ready tag=0x0 len=164
scsi-generic: scsi_read_data tag=0x0
scsi-generic: Command complete 0x0x10a452d0 tag=0x0 status=0
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170120162527.66075-2-farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that CPUs show up in the help text of "-device ?",
we should group them into an appropriate category.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1484917276-7107-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wei Huang